CHECKLIST OF PORTABLE TANDEM STROLLER & CAR SEAT
Thoroughly review the legend on the left. We will use the legend in further steps of this instruction.
Note：Some of the parts have already been assembled, and there are no missing pieces.
Step 1
Opening the Frame
To open the frame, release the locking catch and lift the handle upwards until it locks into place.
Warning: Make sure all locking devices are engaged before use.
Step 2
Assembling the Front Wheels
Insert the metal stem of the front wheels into the wheel holders and push upwards until it clicks into place. (Fig. 2a)
To choose between a fixed or swivel wheel, slide the lock to the side. To remove the wheel, press the button and pull the wheel down. (Fig. 2b)
Step 3
Assembling the Rear Wheels/Brake Unit
Attach the rear axle/brake unit to the rear legs. (Fig. 3a)
Ensure the silver push pins are visible through the hole. (Fig. 3b)
Insert the stems of the rear wheels into the axle unit until they click into place. To detach the wheel, pull down on the clip and remove the wheel. (Fig. 3c)
Step 4
Operating the Brakes
To use the brakes, step on the back of the brake pedal to engage, and push forward on the front of the pedal to release them.
WARNING: Always engage all the brakes when parking the stroller.
Step 5
Attaching the Seat Unit
Before attaching the seat unit to the main frame, ensure the metal bar is positioned underneath the Velcro flap. (Fig. 5a)
Connect the adaptors, numbered 9 and 10, to the main frame and lock the adaptors marked 9. (Fig. 5b)
Step 6
How to fold
Upon completion of installation, inspect the fittings on all four sides of the fence to ensure they are level with each other.
Locking the Top: Twist all the knobs on top of the vertical pipes clockwise to ON to lock them.Turn them counterclockwise to OFF to unlock.
Locking the Bottom: Push down on the suction. Lift it up to unlock..Cup locking device at the bottom of the vertical pipes to lock it.
*Warning: Children should not play inside the fence if the locking devices above and below are not securely locked, otherwise, it could be very dangerous!
Step 7
Folding Storage
Unzip the zippers at the four corners, loosen the fabric (making sure not to be too tight) and unlock the locking devices at the top and bottom of the eight vertical bars, then the baby playpen can be folded and stored.
CHECKLIST OF STANDARD PLAYPEN
Thoroughly review the legend on the left. We will use the legend in further steps of this instruction.
| Fence Dimensions | ① | ② | ③ | ④ | ⑤ | ⑥ |
|---|---|---|---|---|---|---|
| 70" x 60" | 845mm x8 | 695mm x4 | 620mm x7 | x6 | x4 | x4 |
| 80" x 60" | 945mm x8 | 695mm x4 | 620mm x7 | x6 | x4 | x4 |
| 80" x 70" | 945mm x8 | 845mm x4 | 620mm x7 | x6 | x4 | x4 |
Step 1
installing the basement
Unfold the cloth cover, determine the length and width direction, and install the bottom "④ direct pipeline" first. Then insert the corresponding steel pipe, each steel pipe should be installed in the order of "middle first, then sides".
Step 2
setting up the connector
After installing the bottom part, connect the "⑥ Suction cup tee" to the corner pipe. Then install the upper "④ direct pipeline" and connect it to each steel pipe, finally connect it to the corner "⑥ Suction cup tee".
Step 3
setting up the gate
After installing the main fence body, connect it to the gate fence panel to complete the installation.
Note
*Make sure the zipper puller is securely fixed to the hook to ensure safety.
Still Need Assistance?
Our knowledgeable and friendly representatives are here to assist you with any questions or concerns you may have. We understand that some problems may require a more personalized approach, and we are committed to ensuring your satisfaction.
