CHECKLIST OF CASTLE PLAYHOUSE
Thoroughly review the legend. We will use the legend in further steps of this instruction.
| Description | Qty | |
|---|---|---|
| ① | Side Panels | 4 |
| ② | Storage Box Bottom | 3 |
| ③ | Small White Nuts | 12 |
| ④ | Cross Installation Tool | 1 |
| ⑤ | Drawing Board / Activity Table | 1 |
| ⑥ | Large Gray Nuts | 8 |
| ⑦ | Slide | 1 |
| ⑧ | Slide Side Rails | 2 |
| ⑨ | Foot Pedals | 2 |
| ⑩ | Curved Base Pieces | 4 |
| ⑪ | Medium Nuts | 40 |
| ⑫ | L-Shaped Support Brackets | 8 |
| ⑬ | Arched Ring Pieces | 2 |
| ⑭ | Roof Support Rods | 8 |
| ⑮ | Roof Fixing Disc | 1 |
| ⑯ | Reinforcement Disc | 1 |
| ⑰ | Door Curtains | 2 |
| ⑱ | Roof Canopy | 1 |
| ⑲ | Roof Ball Finial | 1 |
| ⑳ | Suction Cups | 8 |
| ㉑ | Storage Box | 2 |
Step 1
Lay ① with the lettered side facing down. Insert ②, then attach the other Side Panels ①. Tighten both sides with ③ using the ④.
Step 2
Stand that side-panel assembly up and slide the ⑤ into the center slots. Secure both sides with the large gray screw caps ⑥.
Step 3
Attach the two panels ⑧ to the slide ⑦ — one on each side — and fasten them with the ③. This completes the slide module.
Step 4
Take the other two panels ① and install the ⑨ between them. Fasten both sides with the ⑥. Stand this step module up, then attach the slide module from Step 3 to the top of it.
Step 5
Snap two pieces ⑩ together to form a semicircle. Place the play-table module (from Step 2) on top of that semicircle and secure underneath with the ⑪.
Step 6
Attach the two L-shaped support plates ⑫ marked “1” and “2” to the sides of the play-table module. Tighten them from the bottom with the ⑪.
Step 7
Make the other semicircle by snapping the remaining two ⑩ together, then mount the slide module on that semicircle. Repeat Step 6 by adding ⑫ to the slide module’s sides.
Step 8
Connect the slide module and the play-table module together by joining their ⑩ so they form a single base.
Step 9
Assemble ⑬ into a circle and secure with nuts. Then install all ⑭, lock them in place with the ⑮, and finish with the ⑯ and flip it over. Tighten with ⑪ to complete the roof frame.
Step 10
Place the roof on top of the assembled house. Before securing it, gently spread open the ⑫, hang each ⑰ on both sides, then close the brackets back together and secure with ⑪.
Step 11
Pull the ⑱ over the top, and make sure the seam lines up with the roof frame. Attach ⑳ along the extension line of the seam, then hook the inner loops of the roof cover onto the suction cups.
Step 12
Install the roof ball ⑲ on top. Place the storage bins ㉑ into the trays. All done.
Great job—your Castle Playhouse is all set up and ready to go. Now let’s kick off the fun!
Still Need Assistance?
Our knowledgeable and friendly representatives are here to assist you with any questions or concerns you may have. We understand that some problems may require a more personalized approach, and we are committed to ensuring your satisfaction.
