Multifunctional Baby Climber User Manual
CHECKLIST OF MULTIFUNCTIONAL BABY CLIMBER
Thoroughly review the legend. We will use the legend in further steps of this instruction.
| Description | Qty | |
|---|---|---|
| ① | Snap-Lock Buckles | 6 |
| ② | Side-Guard Panel | 8 |
| ③ | PivotLink Rod | 3 |
| ④ | 3-in-1 Fun Board(Draw,Build & Write!) | 1 |
| ⑤ | Grip-Tight Screws | 24 |
| ⑥ | Mini Wrench | 1 |
| ⑦ | Safety Gloves | 1 |
| ⑧ | Climbing Rails | 12 |
| ⑨ | White Strut | 2 | ⑩ | Hex Nuts | 16 | ⑪ | Epic Slide | 1 | ⑫ | Leash-Lock Strap | 2 | ⑬ | Heavy-Duty Bolt | 12 | ⑭ | ConeCap Connector | 12 | ⑫ | L-Brace Bracket | 6 |
Here’s a fun, breezy guide to turn your climber into a building-block art desk:
Step 1
Use part ① as a little riser under your base.
Slide two ③ and the ④ into ②.
Cap it with the matching ② on top, then lock everything in place with fittings ⑤, ⑥ and ⑦.
Step 2
On each side of your panel, attach parts ②, ⑧ and ⑨ in that order.
Tighten with bolts ⑤ & ⑥.
Snap on the protective caps ⑩ to keep it rock-solid.
Step 3
Stand your assembly upright and give it another twist of ⑤ & ⑥ for good measure.
Fold both ladders inward at a 90° angle and clip their tops onto rods ③ using parts ①.
Pop on the last two ⑩, tighten, and—voilà!—your building-block art desk is ready for masterpieces.
Z-Board Mode – Let’s rock that Z shape!
Step 1
Re-do the basic hookup: snap Part ②, Part ③ and Part ④ together on one side of the board (Tip: You only need to attach one side of the board with a single ③.).
Step 2
On that same side, slide in Part② + ③, then add Parts ⑧ & ⑨, cap with two more Part 2s, and tighten everything with bolts ⑤, ⑥ & ⑩.
Step 3
Fold the assembled panel into an Z shape. Secure the joints with parts ① and ⑩. Repeat the same steps on the other side, and then stand it up—voilà! Your climbing adventure can begin!
Get ready for some fun with our climbing frame and slide!
Step 1
Grab a piece of ②, and attach pieces ③ and ⑧ to it. Top it off with another ②, and secure it with ⑤ and ⑥. Repeat this to create two ladder sections, then arrange them in a “V” shape. Use ① and ⑩ to lock the sides in place.
Step 2
Connect the third and fourth ladder sections just like before.
Step 3
Shape your assembled ladders into a cozy little playhouse! Secure the joints with ① and ⑩ again. Finally, snap on the slide, and voilà! You’re all set for climbing and sliding adventures!
Great job—your Multifunctional Baby Climber is all set up and ready to go. Now let’s kick off the fun!
Still Need Assistance?
Our knowledgeable and friendly representatives are here to assist you with any questions or concerns you may have. We understand that some problems may require a more personalized approach, and we are committed to ensuring your satisfaction.
