Thoroughly review the legend. We will use the legend in further steps of this instruction.
| Parts Name | Quantity | |
|---|---|---|
| ① | Frame | x1 |
| ② | Seat | x1 |
| ③ | Handlebar | x1 |
| ④ | Front Wheel Frame | x12 |
| ⑤ | Rear Wheels | x2 |
| ⑥ | Foldable Pedals | x2 |
| ⑦ | Front Toddler Footrest | x1 |
| ⑧ | Seat Fabric Cover | x1 |
| ⑨ | Safety Guardrail | x1 |
| ⑩ | Sun Canopy | x1 |
| ⑪ | Push Handle | x1 |
| ⑫ | U-shaped Connector Rod | x1 |
| ⑬ | Basket | x1 |
| ⑭ | Storage Bin & Pouch | x1 |
| ⑮ | Brake Assemblies | x2 |
| ⑯ | Rear Wheel Axles | x1 |
| ⑰ | Steering Shaft | x1 |
| ⑱ | Large Nut & Large Screw Set | x1 |
| ⑲ | Guardrail Fixing Rings | x1 |
| ⑳ | Full Hardware Kit | x1 |
The following is the assembly method of the Versatile Tricycle Stroller.
step 1
Flip the ①frame. Remove the bottom screw/nut, add the ⑥Foldable Pedals, and tighten with the hex key.
step 2
Unscrew the front-bottom bolt on the ①Frame. Flip the ①Frame, fit the ⑦Front Toddler Footrest, and tighten.
step 3
Pop off the two black locks a & b at the top of ①Frame. Slide b onto the top of the ④Front Wheel Frame—press the spring to click. Join ④ to ①, then cap it with a to lock.
step 4
Clip the ⑬Basket onto the ③Handlebar. Mount the ③ to ①—press down until the red latch pops. Flip that red latch up to fully secure.
step 5
Attach the ⑮Brake Assemblies to the left and right rear of ①. Slide the ⑯Rear Wheel Axles through both ⑤Rear Wheels and install the assembly onto ①. Make sure both wheels are solid.
step 6
Remove the screw from the ⑰Steering Shaft. Hook its hooked end into the round hole on the ④Front Wheel Frame. Route the other end under ① to the rear support, pass through the hole, then tighten the screw and nut. Note: ⑰ must sit under the ⑦Front Toddler Footrest.
step 7
Click ②Seat onto ①. Feed the ⑱Large Nut & Large Screw Set up from under the ② and tighten snug. Solid as a rock.
step 8
Slide two small ⑲Guardrail Fixing Rings onto the skinny end of the ⑨Safety Guardrail. Insert both ends of ⑨ into the two seat posts, then lock with the two large Rings ⑲. Click, click—secure.
step 9
Pull the ⑧Seat Fabric Cover over ②Seat. Thread it around the ⑨Safety Guardrail, then snap the bar closed.
step 10
Push the ⑩Canopy onto the two rear mounts behind the ②Seat until it clicks. Shade on.
step 11
Join the ⑪Push Handle to the ⑫U-shaped Connector Rod. Press the spring button, slide through, and lock. Remove the cap from the rear support tube on ①, insert the ⑪, click in, then tighten with ⑳Screw.
step 12
Attach the ⑭Storage Bin & Pouch. Remove the big rear screw on ①Frame, position the ⑭, run the big screw back through, and tighten.
Great job—your Versatile Tricycle Stroller is all set up and ready to go. Now let’s kick off the fun!
Still Need Assistance?
Our knowledgeable and friendly representatives are here to assist you with any questions or concerns you may have. We understand that some problems may require a more personalized approach, and we are committed to ensuring your satisfaction.
