Adult-Accessible
CHECKLIST OF FOLDABLE PLAYPEN
Thoroughly review the legend on the left. We will use the legend in further steps of this instruction.
| Fence Dimensions | ① | ② | ③ | ④ | ⑤ | ⑥ |
|---|---|---|---|---|---|---|
| 70" x 60" | 845mm x8 | 695mm x4 | 620mm x7 | x6 | x4 | x4 |
| 80" x 60" | 945mm x8 | 695mm x4 | 620mm x7 | x6 | x4 | x4 |
| 80" x 70" | 945mm x8 | 845mm x4 | 620mm x7 | x6 | x4 | x4 |
Step 1
Assemble the Door
Take accessories ⑩, ⑪, ⑫and complete the splicing. Open all the zippers of the cloth cover, then insert the steel pipe into the cloth cover, zip up the zipper, and complete the assembly.As indicated by the red circle, make sure that the zipper of the cloth cover is on the same side as the latch of the door. Complete the assembly of the door
*The specifications of the fence are different, the lengths of the accessories of ⑧、⑨ are different, but the structure of all "doors" is consistent, and the installation methods are the same.
Step 2
Orientation of the "Round Switch"
Pay attention to the contrast, the orientation of the "round switch" is different. The "round switch" on the upright pipe at the corner faces the inside of the fence .The "round switch" on the upright pipe in the middle faces the outside of the fence.
Step 3
Assembling the Frame
Insert the steel pipes into the fabric sleeves holes one by one, then connect them with the upright pipes.
Step 4
Assembling the door
Assemble the "door" with the main body.
Step 5
Ensuring a Secure Fit
Make sure that zipper going around the outside of the main playpen is zipped up tight.
(Make sure those steel pipes are snug inside the fabric cover holes.)
Step 6
How to fold
Upon completion of installation, inspect the fittings on all four sides of the fence to ensure they are level with each other.
Locking the Top: Twist all the knobs on top of the vertical pipes clockwise to ON to lock them.Turn them counterclockwise to OFF to unlock.
Locking the Bottom: Push down on the suction. Lift it up to unlock..Cup locking device at the bottom of the vertical pipes to lock it.
*Warning: Children should not play inside the fence if the locking devices above and below are not securely locked, otherwise, it could be very dangerous!
Step 7
Folding Storage
Unzip the zippers at the four corners, loosen the fabric (making sure not to be too tight) and unlock the locking devices at the top and bottom of the eight vertical bars, then the baby playpen can be folded and stored.
CHECKLIST OF STANDARD PLAYPEN
Thoroughly review the legend on the left. We will use the legend in further steps of this instruction.
| Fence Dimensions | ① | ② | ③ | ④ | ⑤ | ⑥ |
|---|---|---|---|---|---|---|
| 70" x 60" | 845mm x8 | 695mm x4 | 620mm x7 | x6 | x4 | x4 |
| 80" x 60" | 945mm x8 | 695mm x4 | 620mm x7 | x6 | x4 | x4 |
| 80" x 70" | 945mm x8 | 845mm x4 | 620mm x7 | x6 | x4 | x4 |
Step 1
installing the basement
Unfold the cloth cover, determine the length and width direction, and install the bottom "④ direct pipeline" first. Then insert the corresponding steel pipe, each steel pipe should be installed in the order of "middle first, then sides".
Step 2
setting up the connector
After installing the bottom part, connect the "⑥ Suction cup tee" to the corner pipe. Then install the upper "④ direct pipeline" and connect it to each steel pipe, finally connect it to the corner "⑥ Suction cup tee".
Step 3
setting up the gate
After installing the main fence body, connect it to the gate fence panel to complete the installation.
Note
*Make sure the zipper puller is securely fixed to the hook to ensure safety.
Still Need Assistance?
Our knowledgeable and friendly representatives are here to assist you with any questions or concerns you may have. We understand that some problems may require a more personalized approach, and we are committed to ensuring your satisfaction.
